Tuesday, June 12, 2012

Big Thanks!

I have been thinking about my statement in a previous post about their being too many people to thank and that is just not true.  So here are some of the notable people that I want to thank for helping me successfully complete this huge undertaking.

1) Rob for giving me a great deal on a great car.
2) Eric Langbein for modifying the car to accept he Honda Fit engine and for imparting some of his knowledge to me.  I look forward to working with him more and learning a lot more!!
3) Tim Minor for answering all my questions and sharing his wealth of experience and knowledge with these cars to me.  Btw, if anyone in the Fairfax, VA area needs a good mechanic -- take your car to Tim Minor's shop -- Automotive Specialist Center.
4) Jeremy Grenier of Ski Motorsports for sharing all the cool things that he has done with his FF.  I just hope I can be as fast as him!
5) My good friend Bruce for his continued support. 
6) Brad Baytos of Primus Racing for helping me figure out what I need and for giving me some great deals!
7) Dave and Warren at Everware-CBDI (the company I work for) for giving me the time off when I needed it to finish up the car and for always supporting me in this racing hobby.
8) And most importantly, my beautiful wife (and crew) Terry.  Without her support, absolutely none of this would have been possible -- and it definitely would not be any fun without her!!  THANKS TERRY!!!

Finally Got To Drive It!!

Well, I drove it last Friday and it was AWESOME!!  I took the car to Eric Langbein's shop the Tuesday before and we did a complete set-up (which went pretty smoothly) and he finished making my shift linkage.  It really felt comfortable right out of the box -- mostly due to the "safe" (more towards understeer than oversteer) setup that Eric put on the car.  The only time you need to use the clutch is to get going so I was left braking and I found out that I really need to work on my shifting.  I just need to perfect the timing of the throttle blipping with the engaging of the lower gear when I'm down shifting.  I pretty much have the upshifts down although they can use some improvement as well.  I did go faster every session and here is a video of my fastest lap.  But this by no means a fast lap -- I left lots of time on the table!  Btw, the gear numbers are not correct.  For some reason it jumps from 2nd to 4th instead of 2nd to 3rd.



Driving the car was great but we did have one issue that we expended a lot of time and effort on.  Unfortunately the data system was showing that I was losing fuel pressure in the corners.  Here is what we were looking at:


The blue line shows lateral gs (in other words, the peaks and valleys show left and right hand corners) and the red line shows the fuel pressure.  There is definitely a correlation between cornering and the fuel pressure dropping and we did lots of things to try to resolve the issue but to no avail.  As a result, I decided to withdraw from the race weekend.  However, I'm glad I did because I was tired!!  I hadn't driven a race car in over a year and driving this car took a lot out of me! 

We really thought that there was an issue with the fuel cell (which is brand new) so I planned to call the manufacture on Monday.  I did pull the fuel cell over the weekend after I pumped the fuel out of it using the fuel pump and there was virtually no fuel left in it -- which meant that the pickup seemed to be working the way it should.  I could also tell that the pickup was fastened to the bottom of the cell.  So these two facts pretty much ruled out the cell as being the issue.  The one fact that was sticking in my mind was that I never got real consistent fuel pressure readings.  I actually thought of this before I pulled the cell but my fuel pressure sensor was mounted in a 45 degree fitting in the fuel regulator.  I used the 45 degree fitting due to space limitations and I think that there might have been an air bubble in that fitting.  I moved the fuel pressure sensor to a different location and no more fluctuation of fuel pressure!  I'm cautiously optimistic that fixed the problem but I obviously need to run the car again to be sure.

Overall it was a great day.  I got a good feel for the car and I will practice the timing of my shifting using my online simulator.  If the worst problem is an air bubble in front of the fuel pressure sensor than that isn't so bad!

Sunday, June 3, 2012

After Graphics!

Well, here she is!




It is about 95% complete and I will be taking it to Eric Langbein's shop this week to get a complete set-up and a modified shift linkage.  There is actually one graphic missing -- the WWP website.  It will go on the sidepods but the graphics company forgot to give it to me wo I will get it from them this week. 

I again spent an incredibly long time in the garage this weekend though.  The graphics took a while to apply but I also calibrated the shock sensors and I wanted to make sure that they were truly linear so I created a chart comparing the voltage produced by the sensor as the arm moves to the amount that the shock moves.  I was a little concerned that the curve wasn't going to be linear but it turns out that the curve was linear which was good news. 

That was good news but I also ran into an issue.  I was running the engine again and monitoring the sensors with my computer and noticed that the battery voltage really dropped when I reved the engine.  Since this car has an alternator, the voltage should be increasing.  Well, it turns out that I didn't hook up the positive pole on the alternator so that it could charge the battery!  It took a while for me to figure that out and changing the wiring was no small task.  However, I'm really glad that I found that issue before I got to the track because there is no way that the battery would last more than 2 sessions without an alternator charging it. 

I also finished the seat.  I had to trim it some more and I covered it with gaffers tape.  I'm really happy with how it turned out.  Here it is with the seat belts installed.


Converting this car from an F2000 to a F1600 car has certainly been a lot of work but has been well worth it.  Frankly, I love the challenge of projects like this.  A lot of people have helped me along the way, really too many to mention.  But that is the good thing about this kind of racing, there is always someone willing to help you if you need it.  Racers are really great people.

The blog isn't done though.  I still need to make a scoop/cold air box and I will be documenting that process.  Plus, I plan on at least posting at least one in car video after next weekend.  I'm sure that I have a lot to get used to in regards to driving it I know that there are many more challenges to come in regards to learning about how to optimize the car's set-up and I look forward to those challenges just as much as the challenge of the build.

Friday, June 1, 2012

Before Graphics

I still have some work to do but here is a pic of her before the graphics are applied.

Monday, May 28, 2012

The Home Stretch!

I'm really pushing to get the car finished for a test day on June 8th and possibly a regional race that weekend.  So I took Friday off from work and since today was a Memorial Day, I was able to spend four days in the garage -- which turned out to be very hot!!  I made a lot of progress but unfortunately material for the blog suffered because I forgot to take as many pictures as I have taken for previous blog entries.  But here ae a few pics to at least show the progress that I have made.

With the help of my beautiful wife and crew (Terry) I was able to get the front suspension on.  It was a little difficult because of the suspension mounting within the bodywork in a number of spots and it is hard to get to those mounting points inside the car.


I was able to get both wheel speed sensors intalled in the front of the car.  The car came with one installed and I just copied the brackets to make brackets for the other side.  The sensor detects a magnet that is mounted on the inside of the hub and you input the tire size in the data system software as well as the number of magnets that the sensor is supposed to detect and the software can then determine the miles per hour.



I was also able to make my first gear change!  It probably took me about 5 times longer than it should have but at least I learned a lot and am confident that I will get better and faster at changing gears.




I was also able to get the rear suspension on the car and the rear axles.  There are CV joints on either side of both axles and I re-packed those with new grease.  I ran into some difficulties here in this task and had to replace a couple of CV boots but I figured everything out. 

Before putting the car back down on the ground I wanted to install some screens to keep debris out of the radiators.  I used some hardware cloth from Home Depot and decided to mount them to the ducts that sit over the radiators and mount inside the side pods. 









In order to give the screen more support, I mounted a piece of 1/2" wide aluminum along the bottom of the screen to hold it to the bottom of the sidepod.



Finally it was time to put it back on the ground!!  I used my engine hoist to lift the car and then lowered it on some stands just higher than the legs of the engine hoist. 



I was then able to work each end to the ground with my quickjack and here she is on the ground!



Next, I needed to make a seat.  Even though a fiberglass seat came with the car, all the things that I changed in the cockpit made it very difficult for me to use it.  Plus, I also wanted to try making a bead seat -- which is basically a bunch of small styrofoam beads that are held together with resin.  There is lots of information on the internet about how to make a bead seat but the first thing you do is determine how many beads you need by putting a bag of beads in the car and sitting it to determine if that is the right amount of beads.  However, before you can do that, you need to line the inside of the cockpit with cardboard to prevent the beads from getting in between the chassis tubes and other nooks and crannies.  Also, you tape some thick plastic over the cardboard and other areas to prevent the bag of beads from getting punctured.


The kit came with 12 gallons of beads and I ended up using 7 gallons.  The bag is a vacuum bag and you hook up a shop vac to it to suck the air out of the bag.  You can do this before the resin is mixed in with the beads to make sure that the amount of beads is sufficient.  After that is done, you mix resin in with the beads and put the bag back in the car.  You then get to sit in the car for 45 minutes with the vacuum running for 45 minutes.  The resin actually doesn't fully set in the time period and it is left in the car for 12 hours.  Again, Terry helped me through this whole process and we decided to do this last step late in the evening so that the seat could set overnight.  When I looked at the seat after I got out of the car, I noticed that some of the aluminum fuel cell cover wasn't covered by the beads so the next morning I cut a section of the bag away from that area and mixed a small amount of beads and resin in a food storage bag so that I could place them in that part of the seat.  I put a kitchen garbage bag over that area and sat in the car for another 45 minutes.  I had already started trimming the seat when I took this picture but you can see the rectangular area where the patch work was performed.



And here is a pic of the seat in the car with most of the trimming done.  Next, I'm going to cover it with gaffers tape and that will ensure that all of the beads are kept in place.



The instructions say to remove all of the bag but there are so many folds that go into the beads that I'm just going to leave the bag there and tape over it.  You can also glue material over the seat but the taping is obviously the quickest method.  It looks like it will work out well though!







Monday, May 21, 2012

Fire Exinguisher

In another post, I mentioned that I had to order a new fire extinguisher because the one that came with the car had a slow leak.  At first I ordered a mechanical fire extinguisher but I couldn't get that one too fit due to the overall length and the handle was getting in the way of other things.  So I sent that one back and exchanged it with the electric version.  It is actually a really nice system that has its own control panel which has batteries to activate the extinguisher if needed.  You can also flip a switch to arm and de-arm the system.

Here is a pic of the extinguisher installed.  You can see the extinguisher tubing and the electrical cable mounted to the extinguisher.



And here are pics of the control panel which is velcroed to the bodywork and the button that I would push if there was a fire.












I did not take pics but there is a nozzle in the cockpit area and one in the engine bay.

Due to the straps and latches that hold the extinguisher in place which my feet could hit getting in and out of the car, I decided to make an aluminum cover.  In order to figure out the shape of the cover, I again turned to using the thin 1/2 inch steel to get the shape.


When bending the aluminum, I layed the steel template next to the aluminum on my metal brake so that I could match the angles.  Take a note of the metal brake that I'm using in the pic below.  I bought this from Harbor Freight many years ago for something like $20.  It certainly isn't an optimum piece of equipment but for tasks such as this it actually does a decent job.


Here are some pics of the cover installed.









Unfortunately, I got in the car and found out that my calves were hitting the cover!  And after looking at these pictures, I have realized why -- the cover is much higher than the battery and the template was not that high.  Oh well, I can probably modify it but I can also drive the car without it so this is probably something that I will re-visit after the first test day. 

Undertray Part 2

Continuing on with the undertray, I was able to fiberglass the edges during the evenings last week.  I used a very light fiberglass cloth and put two layers on each edge.  I could only do one edge at a time because I had to let the resin harden and trim off the excess cloth before moving onto the next edge.  Unfortunately bubbles are hard to avoid when trying to wrap around such sharp edges unless you are vacuum bagging -- and I don't have the vacuum bagging equipment.  The first side that I did had more bubbles then I would prefer so I used a fiberglass filler that you can mix in with the resin when laying up the remaing edges.  The cool thing about fillers is that you can add a little bit at a time to get the consistency that you want and then it will harden at the same rate as the cloth after you have layed it on top.  Here is a pic of one of the sides with the filler -- which is white.


I also fiberglassed the top side and I used a heavy piece of fiberglass cloth and then put a light layer on top of that.



After the resin hardened, I put a layer of "icing" which is basically a finishing puddy that is much easier to spread then the standard bondo.  It is mainly used for filling in pinholes and other small imperfections but it worked well here because the light fiberglass cloth has a really tight weave and it is a flat surface so it was especially easy to spread it.  After the first application I sanded it down with 180 grit sandpaper and then applied another layer and sanded again.  It was now time to mount it to the car so that all the holes would be drilled prior to paint.

I'm mounting the undertray to the side pods with a couple of strips of aluminum.  I'm not ecstatic about this approach but it will work for now and I probably won't use the large washers when I permanently mount it so that alone will make it look better.  Plus I think the aluminum will look a lot better after it is painted red.  It is something that I can easily change later if I want.



After I got the front secured, I needed to come up with a way to support the back.  At the last race I was at, I noticed that some cars used metal straps to do this.  I had some thin 1/2 inch wide steel so this is what I decided to use.  However, it was a litle bit of a challenge to figure out the exact length and the bends so I could another piece of 1/4" plywood that was only about 4 inches thick and put this where the undertray would go.  This allowed me to extend the steel past the plywood and helped me figure out where to bend the steel to get the shape and length that I wanted.


And here is a pic of the undertray mounted -- and I dropped it off with my paint guy today!